| WorldWorksGames http://www.worldworksgames.com/forum/ |
|
| Plotter Kit for Craft Robo http://www.worldworksgames.com/forum/viewtopic.php?f=62&t=8546 |
Page 1 of 1 |
| Author: | TheAuldGrump [ 07-12-2010, 08:01 PM ] |
| Post subject: | Plotter Kit for Craft Robo |
Hmmm, they now sell a to use with the Craft Robo - turning it into a regular plotter. I don't know if anyone here would find it useful, but it is interesting. 
The Auld Grump *EDIT* Link Looks good.... *EDIT 2* Link works for me, I don't know what's wrong.... |
|
| Author: | Talae [ 07-12-2010, 09:37 PM ] |
| Post subject: | |
Dead link for me 
|
|
| Author: | TheAuldGrump [ 07-12-2010, 10:05 PM ] |
| Post subject: | |
. I think Craft-e may have sold out. Their links disappear when they do that.... The Auld Grump *EDIT* The first link still works fine for me. And they have not sold out. Maybe they don't like linking for some reason, or I am loading from cache? |
|
| Author: | Talae [ 07-12-2010, 11:12 PM ] |
| Post subject: | |
Works now, but didn't before. It is definitely an interesting concept. |
|
| Author: | morganm [ 07-13-2010, 05:01 AM ] |
| Post subject: | |
I wonder... if you ran a print out through with the blade on and then swap the blade for a pen and ran it through again... would it edge for you? Would it actually get down in the cut line yet still get ink along the edge? Just a thought I had when I read your post... |
|
| Author: | Zenguy [ 07-14-2010, 01:24 AM ] |
| Post subject: | |
| Author: | SoBaldrick [ 09-16-2010, 06:31 AM ] |
| Post subject: | |
| Author: | SoBaldrick [ 11-12-2010, 03:39 AM ] |
| Post subject: | |
Well, the pens have arived, so i'll give them a go the weekend and post results... |
|
| Author: | Talae [ 11-12-2010, 08:54 PM ] |
| Post subject: | |
| Author: | SoBaldrick [ 11-13-2010, 06:59 AM ] |
| Post subject: | |
Well tried them out today, and they work fine.. This is the Packaging They fit in the Craft Robo fine, except that you can't close the lid as it hits the top of the pen.. As for results, nice clean lines 0.45mm thick.. Sob |
|
| Author: | morganm [ 11-30-2010, 08:07 AM ] |
| Post subject: | |
| Author: | Talae [ 11-30-2010, 06:26 PM ] |
| Post subject: | |
| Author: | SoBaldrick [ 12-06-2010, 02:04 AM ] |
| Post subject: | |
| Author: | Talae [ 12-06-2010, 11:45 AM ] |
| Post subject: | |
| Author: | Solospirit [ 12-06-2010, 03:51 PM ] |
| Post subject: | |
There is a pen holder available for it...So it would not be a problem to set it up with markers...But...I can see that it would be very fussy to set up so that it would bleed down into the edge, but not over onto the part..Im skeptical that it would be a practical edging tool...shame really
|
|
| Author: | Talae [ 12-06-2010, 07:17 PM ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC - 8 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|